MATERIAL SAFETY DATA SHEET

 

PRODUCT: PROTECTIVE PACKAGING NETS

 

  

  1. PRODUCT INFORMATION
    2.

    Not a WHMIS controlled product

  2. INGREDIENTS OF PRODUCT
    3.

    Polyethylene Resin 99-100% wt/wt

  3. HEALTH HAZARD INFORMATION

AFFECTS OF ACUTE AND CHRONIC EXPOSURE

SKIN

Direct contact with product may cause dermatitis (skin inflammation) in sensitive individuals. Contact with molten will burn unprotected skin.

EYES

Irritation may result from the physical presence of any of the product or parts of the product in the eyes.

INHALATION

Small particles inhaled may cause mild respiratory tract irritation

INGESTION

No known health hazard appears to be posed by the ingestion of small amounts of the product. A physician should be consulted if large amounts are ingested.

OCCUPATIONAL EXPOSURE LIMITS

Airborne particles of the product should be considered a nuisance dust. The American Conference of Governmental Industrial Hygienists (ACGIH) has established an Occupational Exposure Limit (TLV-TWA) of 10 milligrams per cubic metre of air for Particulates Not Otherwise Classified (i.e., nuisance dust).

 

 

TOXICITY DATA

LD /LC DATA No test data available for routes of inhalation or ingestion

REPRODUCTIVE EFFECTS No reproductive effects

MUTAGENIC EFFECTS No mutagenic effects

CARCINOGENICITY Not carcinogenic (by OSHA, NTP Or IARC)

FIRST AID INFORMATION

 

SKIN

Wash contaminated skin with soap and water. Individuals experiencing skin sensitivity should obtain

medical advice. Should a burn occur, cool burn area emmediately with cool, clean, running water

until no heat is emitted from burn area. Cover with light, dry dressing. Do not apply ointments or

puncture blister. Obtain medical assistance.

EYES

Remove dust particles by flushing eye with clean water. Seek medical attention.

INHALATION

If respiratory irritation occurs, remove affected personnel from the work area. Obtain medical

attention if irritation persists, or if severe. Implement appropriate controls to prevent further

exposure (refer to section 8)

INGESTION

Consult a physician if pain or discomfort occurs.

5. FIRE AND EXPLOSION HAZARD DATA

FLASHPOINT Not applicable

AUTO IGNITION TEMP 330 C – 410 C (630 F- 770 F)

FLAMABLE LIMITS Non-volatile material

FIRE EXTINGUISHING SUBSTANCE

Water spray, foam or dry chemical using extinguisher manufacture’s recommended application

Techniques.

HAZARDOUS COMBUSTION PRODUCTS

Carbon dioxide, carbon monoxide, aldehydes, acrolein and small amounts of other organic vapours

may be produced.

SPECIAL FIREFIGHTING PROCEDURES

Firefighters must wear NIOSH-approved, self-contained breathing apparatus to provide protection

against combustion products. Evacuate all unprotected personnel.

UNUSUAL FIRE AND EXPLOSION HAZARDS

None noted

  1. REACTIVITY DATA

STABILITY Stable

 

INCOMPATIBILITY None

 

CONDITIONS TO AVOID Temperatures over 325 C(620 F) may cause resin degradation.

HAZARDOUS DECOMPOSITION

At temperatures over 250 C (480 F), carbon monoxide, carbon dioxide, alderhydes, ketones, acids and small amounts of other organic vapours may be produced. Carbon monoxide formation is enhanced under conditions of oxygen starvation.

7. SPILL AND LEAK RESPONSE PROCEDURES

Not applicable.

 

8. EXPOSURE CONTROLS AND PERSONAL PROTECTIVE EQUIPMENT

ENGINEERING CONTROLS

Local and general ventilation must be provided when product is cut using a device which may cause dust particles.

RESPIRATORY PROTECTION

The use of NIOSH-approved respiratory protection is recommended when airbourne dust concentrations or decomposition products cannot be adequately controlled by ventilation. Respiratory protection must be selected to suit the type of contaminant, the concentration of the contaminant and the limitations of the respiratory protective device.

EYE PROTECTION

Safety glasses with side shields should be worn when cutting, where airborn dust particles could enter the eyes. Non-vented chemical goggles should be worn when there is potential for exposure to vapours or combustion products.

PROTECTIVE GLOVES/CLOTHING

Gloves and other skin coverings should be worn by individuals experiencing skin sensitivity. Heat-resistant gloves should be worn when handling molten product
  1. STORAGE REQUIREMENTS
    2.

    Store in area away from ignition sources.

  2. PHYSICAL DATA

    3. PHYSICAL STATE Solid

    ODOUR AND APPEARANCE netting, may have odour

    ODOUR THRESHOLD no data available

    SPECIFIC GRAVITY 910 kg/m –930 kg/m (57 lb/ft –58 lb/ft )

    VAPOUR PRESSURE N/A

    VAPOUR DENSITY N/A

    EVAPORATION RATE N/A

    BOILING POINT N/A

    MELTING POINT 105 c-125 c (221 f- 257 f)

    PH N/A

    Coefficient of Oil/Water Insoluble in both oil and water

  3. REGULATORY INFORMATION

    4. TRANSPORTATION CANADIAN TDG: Not regulated

    USA DOT: Not regulated

    WHMIS-CANADA Not controlled

     

    OSHA-USA Non-hazardous, according to 29 CFR 1910.1200

     

     

    NFPA rating: health= 0; Fire=1; Reactivity=0

    EPA Hazard rating: Non-hazardous

    USA FDA: In compliance with 21 CFR Part 177.1520

    Massachusetts: 105 CMR 670.010D: Not present on substance list.

  4. SUPPLEMENTARY INFORMATION

    5. NOTE TO PHYSICIAN

    Smoke and hazardous decomposition products produced in fires involving polyethylene resins can be irritating and may cause pulmonary edema in severely exposed individuals. As this effect may be delayed in onset, a 72 hour post-exposure observation is recommended. Carboxyhemoglobin levels should also be monitored to asses the degree of carbon monoxide absorption in these individuals.

  5. PREPARATION INFORMATION

PREPARED BY MASTERNET LTD

1236 CARDIFF BLVD

MISSISSAUGA ONTARIO

CANADA

TELEPHONE: 905-795-0005

DATE OF ISSUE FEBRUARY 26, 2004

 

 

 

 

 

 

 

 

 

 

 

Vexar® products now available.